Dehumidifying dryer MJ3

MJ3 provides stable low dew point dry air of -40°C and a vacuum loader on a single platform. This portable unit prioritizes easy maintenance. The initial performance is maintained for a long period without replacing the adsorbent material in the honeycomb unit.

Download general catalog 2023

Features of MJ3

Reliable

Ensures stable drying condition with honeycomb rotor. Independent drying and conveying circuits allows conveyance of materials without affecting drying condition.

Safety

SSR (contactless relay) for the heater control circuit reduces maintenance frequency and greatly improves safety.

Energy saving

Adopting a double hopper improves heat retention and contributes to energy saving.

Compact

Combined dehumidifying dryer and conveyor into a single unit.

Easy maintenance

All filter maintenance can be done from the operational side.

Flow Diagram

Matsui Solutions

Eliminate wasted energy

Waste heat can be reused by installing regenerated waste heat recovery unit.
Up to 26% + α reduction in electricity bill!

Related parts for this product

Parts related to Dehumidifying dryer "MJ3" are available on the following site.

Recommended related products

Cartridge filter for MJ3/MJ5 (MXF-Plascom-G1) -Pluscom-Convenient website for molding sites sites-

Cartridge filter for MJ3/MJ5 (MXF-Plascom-G1) -Pluscom-Convenient website for molding sites sites-

Cartridge filter for Matsui Dehumidifying dryer A filter is installed in each of the drying section and transportation section. Please check the compatible models below before ordering. ■Compatible models (Matsui) ・MJ3-10,15,25J (drying section) ・MJ3-10~150J (transporting section) ・MJ5-i-150,350,650J (drying/transporting section) ・DMZ-40~120 (drying) *This is an old model ・MJ2-15,25 (dry) *This is an old model

Quick Clamp Knob KQC-30-M8-Plascom-Convenient website for molding sites sites-

Quick Clamp Knob KQC-30-M8-Plascom-Convenient website for molding sites sites-

Even long screws can be tightened quickly. ■Features - Pass the screw through the straight hole and move it to the tightening position. Next, raise the knob perpendicular to the screw and tighten.・If the tightening length (A) of the screw is shorter than the total height (H) of the knob, sufficient tightening force will not be obtained.・Make sure that the tightening length (A) of the screw is greater than or equal to the total height (H) of the knob. ■Specifications - Target thread: M8 Model DMH s C d Mass (g) KQC-30-M8 30 M8 17 5 8 20 73 Outer dimensions and structure image

Precautions for installing drying equipment

  1. According to Article 14 of the Industrial Safety and Health Act and Article 6-8 of the Industrial Safety and Health Act Enforcement Ordinance, the business operator who uses power as a heat source for heating and drying is stipulated that a drying equipment work chief must be appointed from those who have completed the skill training for the drying equipment work chief when using and operating drying equipment with a rated power of 10 kW or more. As the skill training for drying equipment work chiefs differs depending on the prefecture, please contact the prefectural labor bureau (labor standards inspection office) in your jurisdiction.
  2. According to Article 88 of the Industrial Safety and Health Act and Article 6-8 of the Industrial Safety and Health Act Enforcement Ordinance, the business operator who uses power as a heat source for heating and drying is stipulated that the notification must be made to the Chief of Labor Standards Inspection Office at least 30 days before the start date of the construction when installing or relocating the drying equipment with a rated power of 10 kW or more and when changing the main construction part.
  3. According to Article 45 of the Industrial Safety and Health Act and Article 15, Paragraph 1, Item 7 of the Industrial Safety and Health Act Enforcement Ordinance, the business operator shall conduct a periodic self-inspection of the drying equipment and keep the record for three years is stipulated. (Related: Industrial Safety and Health Act Enforcement Regulations Article 299)
  4. Drying equipment may require notification to the fire department depending on the municipality. Please contact your local fire department.

If you have any other questions or Contact regarding products, systems, or services, or inquiries regarding prices, please contact us Contact form on our website or contact the Customer Center below.

Contact us by phone

Reception hours: Weekdays 8:30-17:30
Customer center: 042-700-7215

Line up